How To Install Carpet Runner On Curved Stairs

Home - Diy

How to Install Rug on Curved Stairs

Curved or winding staircases are a decorative characteristic of many homes. The placement of mid-staircase landings, or angled steps, redirects the path of the staircase, which allows it to turn corners, or simply add a bit of way to an entryway.

How to Install Rug on Curved Stairs

Carpet curved or winding stairs involves providing enough carpet to make the turns and cover the steps properly, while hiding any details of the installing from sight.

• Tackless strips
• Tape mensurate
• Hand saw
• Hammer
• Nails
• Carpet padding
• Razor knife
• Staple gun
• Carpet
• Stair rods
• Power drill
• Screwdriver
• Piece of work gloves

Tip

Stair rods can exist installed for extra finish and a fleck of extra holding ability to keep the folded pieces of excess carpet held firmly in place against the risers. Gear up one rod beneath the bull olfactory organ at the top of each riser, and united states your power drill to make pilot holes into the face of the riser just outside each border of the rug. Use your screwdriver and the screws provided to fasten the rods in place.

Warning

Apply caution when working with dangerous tools such as razor knives. Serious injury tin occur. Wear work gloves for protection.

1. Install tackless strips to each tread and riser on the staircase. Employ your hand saw to cut the tackless strips to fit the width of the carpet runner you are installing, minus 1 inch on each side. Place ane strip at the dorsum edge of each tread so it sits flush against the riser of the next pace, and so that the tacks face away from the tread. Use your hammer and nails to fasten each tackless strip in place.

2. Install carpet padding along the stairs where the rug volition lie. Cutting and fit the padding to each stride starting from the bottom and working your way upwardly. Place 1 terminate of the padding against the riser at the bottom of the staircase and use your staple gun to drive one staple every 3 inches or and so around the perimeter of the padding. Bulldoze a few staples into the middle portion of the padding as well to keep information technology firmly in place.

3. Pull the padding up over the front of the footstep and drive staples through the padding and into the underside of the balderdash nose for a tight fit. Cut the padding with your razor knife so it stops at the border of the tackless strip and fasten it in place with your staple gun. Repeat the process at each pace all the way upwardly, stopping at the last riser before the upper landing.

4. Install your carpet from the lesser up besides. Place one end of the rug against the corner formed by the floor and the first riser. Drive staples, one every 3 inches across the lesser edge of the carpet to fasten it in place. Pull the carpet upward and attach information technology to the tackless strip at the back of the tread. When you lot accomplish your kickoff curved step, angle the carpet as necessary to go on the carpet centered on the stairs. 1 side of the carpeting will require more material while the other requires less because of the plow being made.

5. Keep the tread carpeting flat and single ply, and staple it the underside of the bull olfactory organ every bit before. When you reach the riser, fold the resulting backlog carpet over onto itself and so that it becomes tucked into a iii-layered bundle. Press the bundle against the surface of the riser, and use your staple gun to bulldoze i staple every three inches or then to fasten information technology in place. Go along to the side by side tread and repeat the procedure. The treads will be evenly covered, and the risers will hide the rest.

The Drip Cap

• Curved or winding staircases are a decorative characteristic of many homes.
  
• The placement of mid-staircase landings, or angled steps, redirects the path of the staircase, which allows it to turn corners, or just add together a bit of way to an entryway.
  
• Identify one end of the padding against the riser at the bottom of the staircase and utilize your staple gun to bulldoze one staple every 3 inches or so around the perimeter of the padding.
  
• Repeat the procedure at each step all the way upwards, stopping at the last riser before the upper landing.
  
• Pull the carpet upward and attach it to the tackless strip at the back of the tread.
  
• Keep the tread carpeting flat and single ply, and staple information technology the underside of the bull olfactory organ every bit before.

Source: https://homesteady.com/12000671/how-to-install-carpet-on-curved-stairs

Posted by: richardintoommand.blogspot.com

Share this post